Support Questions

Find answers, ask questions, and share your expertise
Announcements
Celebrating as our community reaches 100,000 members! Thank you!

Hive Multiple Small Files

avatar

Hi ,

I have large csv files which arrives Hadoop on a daily basis.(10GB). 1 file per day. I have a Hive external table and point it to the files (No partitions / No ORC) - Table1. I have another table Table2(external table + ORC-ZLIB) partitioned by date(yyyy-mm-dd) loaded from Table1 using insert into Table2 partition(columnname) select * from Table1 with hive.exec.dynamic.partition = true enabled. The daily files once compressed via ORC comes to <10MB(this was a surprise to me looking at the compression ratio). I have read about the multiple small file problems in Hadoop from the HW community.

Is there any additional settings in Hive / considerations to be in place so that we don't run into performance issues caused by the multiple small files?

Thanks

Nikkie

10 REPLIES 10

avatar

Hi Nikkie Thomas

To control the no of files inserted in hive tables we can either change the no of mapper/reducers to 1 depending on the need, so that the final output file will always be one. If not anyone of the below things should be enable to merge a reducer output if the size is less than an block size.

  • hive.merge.mapfiles -- Merge small files at the end of a map-only job.
  • hive.merge.mapredfiles -- Merge small files at the end of a map-reduce job.
  • hive.merge.size.per.task -- Size of merged files at the end of the job.
  • hive.merge.smallfiles.avgsize -- When the average output file size of a job is less than this number, Hive will start an additional map-reduce job to merge the output files into bigger files. This is only done for map-only jobs if hive.merge.mapfiles is true, and for map-reduce jobs if hive.merge.mapredfiles is true.

avatar
Expert Contributor

Hi @Bala Vignesh N V, I have similar issue. have done the above settings, but this does not help. I have posted a question on HCC : https://community.hortonworks.com/questions/109365/controlling-number-of-small-files-while-inserting....

avatar

Thanks for your response.If I partition the data by yyyy-mm-dd field and I receive only one file per day. I assume , I will always have one file per partition irrespective of this setting?

If the above assumption is correct(pls correct if that is wrong), will I end up with select queries which runs slower if I store files for say 6 years?

i.e I will have 6 * 365 files each around say 8-9MB in size (which is smaller than the default chunk size).

I was hoping to consolidate the files on a weekly basis but , I need to have data available to users on a daily basis ..hence I dont think I can do that.

Let me know the suggestions.

Thanks

Nikkie

avatar

Nikkie Thomas

If I partition the data by yyyy-mm-dd field and I receive only one file per day. I assume , I will always have one file per partition irrespective of this setting? --> Its not that simple, because it depends on the size of your input file, block size, size of mapper /reducer an other variables. Considering your input file is less than the block size then it should create only one file.

If you partition the table on a daily basis with less size then in growth of time it will cause performance issues and there is not much to do with partition. What I would say on such condition, is that partition the table on yearly basis with buckets on a frequently used filter column. In your case it can be daily/weekly/yearly basis. But still each file in a bucketed folder will be less if the data size is less.

avatar
Guru

@Nikkie Thomas you can specify the number of reducers for a query :

hive> set mapreduce.job.reduces=1;

avatar
New Contributor

Hi,

I found out that when using Tez (an execution engine on Hive) you should use another parameter to get as an output only 1 file:

SET hive.merge.tezfiles=true;

Tez in many cases is faster than MR2 engine, to verify what execution engine you use run on Hive:

SET hive.execution.engine; 

if you want to switch to Tez, just set it etiher in hive-site,xml or for each Hive session:

SET  hive.execution.engine=tez;Best regards,

Michał

avatar

I have 10 files each of size 64GB, a hive table is created on top of these files.

data read operations are slow, thinking 64GB file read is the culprit. file format is text

can someone check this scenario

avatar
Rising Star

@Venkatesh Kancharla open up a new question with all the details. and logs.

avatar
New Contributor

I can see you have already partitioned your tables. One important thing is if you are using hive you need to make sure that the tables are partitioned on the column where most of your data is clubbed. So the date Column in my suggestion is the best option here. 

Also, for those who are new to hive/hdfs, multiple files are created when you load data in hive tables. so don't get confused just pick the right partition and your files will be reduced in hdfs where hive data is being saved.